Search found 1014 matches

by ArT
Tue Oct 20, 2020 7:59 am
Forum: Przykłady Montażu
Topic: Montaż UKP-PRO do Nissan Navara D40
Replies: 1
Views: 2

Re: Montaż UKP-PRO do Nissan Navara D40

Super, dzięki za podzielenie się relacją. Pozostaje życzyć żadnych kolejnych problemów z silnikiem lub wykrywanie ich na bardzo wczesnym etapie 8-)
by ArT
Thu Oct 15, 2020 7:48 am
Forum: Technical Support
Topic: Autodetect IC (mostly SPI)
Replies: 5
Views: 114

Re: Autodetect IC (mostly SPI)

Thank you for your suggestions. One more hint - in REVELPROG-IS there are also 'smart' procedures for FLASH SPI 25 series - you do not have to select specific device - only family and voltage, for example if you select FLASH -> 25 series -> 25..64 [PP] and 3.3V then it will programm you all FLASH 64...
by ArT
Mon Oct 05, 2020 2:07 pm
Forum: Technical Support
Topic: Autodetect IC (mostly SPI)
Replies: 5
Views: 114

Re: Autodetect IC (mostly SPI)

You can find READ ID function in tools -> Read ID and then you will need to select protocol (e.g. SPI 25 series, 1-wire etc) and voltage (because programmer supports also low voltage chips and when you select to high voltage for low voltage chip you can damage it). It will display you ID of memory a...
by ArT
Sun Sep 27, 2020 2:36 pm
Forum: Examples of assembly
Topic: Volvo 940
Replies: 1
Views: 71

Re: Volvo 940

Very nice, thank you for sharing it :)
by ArT
Fri Sep 25, 2020 9:49 am
Forum: Wsparcie Techniczne
Topic: Nowe opcje - ME Region
Replies: 2
Views: 71

Re: Nowe opcje - ME Region

Dzięki za sugestie ;) Spróbuje zapoznać się z tym tematem, sam nie jestem serwisantem PC ale widzę że temat ma ponad 340 stron więc pewnie cała wiedza jest tam dostępna? :)

W ogóle zasada działania i możliwości IME brzmią jak dobre ognisko do szpiegowania użytkownika z zewnątrz ;))
by ArT
Thu Sep 24, 2020 6:50 pm
Forum: UTCOMP News, Updates and Other
Topic: UTCOMP Android app (developement progress)
Replies: 7
Views: 8536

Re: UTCOMP Android app (developement progress)

I think it should be possible to hide it, I added it to "TODO" list ;)
by ArT
Thu Sep 24, 2020 11:28 am
Forum: Technical Support
Topic: FS.COM SFP+ self destruction
Replies: 5
Views: 133

Re: FS.COM SFP+ self destruction

I prepared you custom firmware - please check your PM for more details. Probably you will need to brute force from beginning. If it found password it will be stored in manufacturer name. If you will have timeout again please remember to write down last password it checked - just in case. Please chec...
by ArT
Mon Sep 21, 2020 2:50 pm
Forum: Technical Support
Topic: FS.COM SFP+ self destruction
Replies: 5
Views: 133

Re: FS.COM SFP+ self destruction

Unlocking with the password above returns “Executing operation 1/1...success”, but writing results in a verification error at address 0x14 (the first byte of the manufacturer name). Password search finds the password at every starting point (checked 1 from...) Maybe it thinks it found the password ...
by ArT
Mon Sep 21, 2020 8:56 am
Forum: Technical Support
Topic: FS.COM SFP+ self destruction
Replies: 5
Views: 133

Re: FS.COM SFP+ self destruction

When you have "TEST" in manufacturer name than it found password and it was unlocked for a moment and it should stay unlocked until you disconnect power from SFP (after disconnecting power it will require password again). If it's microprocessor based SFP then password may be variable, it m...
by ArT
Mon Sep 21, 2020 8:42 am
Forum: Poradniki
Topic: Montaż czujnika temperatury oleju oraz ciśnienia oleju 0-10 bar (np. Auto Gauge)
Replies: 7
Views: 46894

Re: Montaż czujnika temperatury oleju oraz ciśnienia oleju 0-10 bar (np. Auto Gauge)

W czujnikach autogauge (i ogólnie czujnikach rezystancyjnych typu "bańka" 2-pinowych) jest ten problem że czasem wyciera się wewnątrz ten suwak rezystancyjny i czasem potrafi na biegu jałowym pokazywać 0 bar a jak tylko lekko dodasz gazu to łapie kontakt i pokazuje prawidłowe ciśnienie. Og...

Go to advanced search