Search found 47 matches

by Kaldek
Tue Mar 23, 2021 11:25 am
Forum: UTCOMP News, Updates and Other
Topic: UTCOMP suggestions for incoming updates
Replies: 47
Views: 41383

Re: UTCOMP suggestions for incoming updates

Hi Artur, It's been a while (five years!) since I last asked but can we please get the ability to read ethanol content. ADC 0-5v is fine - I know I previously asked for PWM but 0-5v is all I need. I would reprogram the icons just using version 3.8 but unfortunately I can't change both the icon and t...
by Kaldek
Fri Aug 07, 2020 11:30 am
Forum: UTCOMP News, Updates and Other
Topic: Update v3.8 for UTCOMP-3 and UTCOMP-PRO
Replies: 12
Views: 17532

Re: Update v3.8 for UTCOMP-3 and UTCOMP-PRO

ArT wrote:Just one notice. If "boat mode" will be activated after import (consumption in l/h or mph only) then you can deactivate it


Hi Artur, mine did this as well. Any idea why the upgrade defaulted to this?
by Kaldek
Wed May 01, 2019 4:38 am
Forum: UTCOMP News, Updates and Other
Topic: Update v3.7 for UTCOMP-3 and UTCOMP-PRO
Replies: 4
Views: 10403

Re: Update v3.7 for UTCOMP-3 and UTCOMP-PRO

Thanks. I installed 3.7.1 and greatly appreciate the ability to slow down my temperature readings.
by Kaldek
Tue Apr 30, 2019 1:46 pm
Forum: UTCOMP News, Updates and Other
Topic: Update v3.7 for UTCOMP-3 and UTCOMP-PRO
Replies: 4
Views: 10403

Re: Update v3.7 for UTCOMP-3 and UTCOMP-PRO

Hi Artur, if we install 3.7.1 will it cause any issues with later updates such as 3.8?
by Kaldek
Thu Mar 07, 2019 4:20 am
Forum: UTCOMP News, Updates and Other
Topic: UTCOMP suggestions for incoming updates
Replies: 47
Views: 41383

Re: UTCOMP suggestions for incoming updates

Can we have the ability to monitor water/coolant pressure please. I think the best way to manage that is to allow us to configure what the name of our outputs are and what they are measuring (i.e. temp or psi). I am currently monitoring: - Water temp via ADC1 - Wideband AFR via ADC2 - Boost pressure...
by Kaldek
Sat Mar 02, 2019 6:40 am
Forum: UTCOMP technical support
Topic: ECT inaccuracy since change NTC change
Replies: 3
Views: 4343

Re: ECT inaccuracy since change NTC change

Could you send me your settings file before update and after update? And your voltage/temp table. I'll check it. Hi Artur, it turns out this was my fault. I had installed a bad radiator cap which caused an air pocket to be trapped in the system and cause inconsistent cooling, which explains the mas...
by Kaldek
Sun Feb 24, 2019 1:57 am
Forum: UTCOMP technical support
Topic: ECT inaccuracy since change NTC change
Replies: 3
Views: 4343

ECT inaccuracy since change NTC change

Since UTCOMP v3.5 and the introduction of "simplified" calibration of NTC sensors, I find that my ECT is now less accurate and the temperature tends to swing wildly (up to 10 degrees C). My sensor taps the ECT sensor feed going to the ECU from the 3-wire 5 volt referenced engine coolant te...
by Kaldek
Sun Jan 20, 2019 4:42 am
Forum: UTCOMP technical support
Topic: Cannot update UTCOMP firmware from 3.4 to anything newer
Replies: 1
Views: 2311

Re: Cannot update UTCOMP firmware from 3.4 to anything newer

Never mind. Performing a full EEPROM clear (CTRL+ALT+SHIFT+R) solved the issue.
by Kaldek
Sun Jan 20, 2019 4:09 am
Forum: UTCOMP technical support
Topic: Cannot update UTCOMP firmware from 3.4 to anything newer
Replies: 1
Views: 2311

Cannot update UTCOMP firmware from 3.4 to anything newer

My UTCOMP Pro has been running 3.4 for a while. I am attempting to update it to 3.5, 3.6 or 3.7 but it refuses. Every time I click "Run DFU mode" the app just comes back and says "This version of UTCOMP is not compatible with this version of application. Software and device version sh...
by Kaldek
Wed May 24, 2017 4:13 am
Forum: UTCOMP News, Updates and Other
Topic: UTCOMP suggestions for incoming updates
Replies: 47
Views: 41383

Re: UTCOMP suggestions for incoming updates

Hi people, As UTCOMP is a universal product. I would suggest for the next update if we have the ability to put a brand Logo like GTI, OPC, TDI ........ or eventualy maybe the ability to personalise it or if you can set it in advance so we can choose what to display. At corners of the screen we woul...

Go to advanced search

cron